Diagnosis
Compression, leak-down, oil pressure and fault codes, before anything is opened.
SNZ Auto Engineering Works repairs, overhauls and rebuilds petrol and diesel engines at our Wilson Garden workshop. Daily drivers, supercars, race cars: if it has an engine, we strip it, measure it and rebuild it to spec. You get a measured diagnosis of what actually failed, a clear repair-or-rebuild plan, and an engine that runs to spec when it leaves. Don't replace it. Rebuild it.
Engine repair fixes one failed part — a head gasket, timing chain, oil pump or injector seal — while the rest of the engine stays in place. A rebuild strips the engine to a bare block and restores it to correct tolerances. Both follow the same seven steps at our Bangalore workshop. Engine work is one of the five services we run from one workshop.
Compression, leak-down, oil pressure and fault codes, before anything is opened.
The engine comes apart in order, so wear marks show what caused the failure.
Bores, crank journals, bearing clearances, deck flatness and ring gaps decide the work list.
Boring, honing, crank grinding, decking and valve work, done in-house.
Replaced only where measurement proves they are out of spec.
Clean, torqued to specification, with clearances checked as we build.
Oil pressure, leaks and a road test before the car comes back.
Engines warn you before they fail completely. Book an inspection if you notice any of these:
Ignoring these does not keep the repair small. Worn rings that a rebuild could have fixed will score the bore and become a far bigger job.
Oil starvation is the most common killer: low oil, a blocked pickup, a failing pump or stretched service intervals let metal contact metal. Overheating distorts aluminium heads, and Bangalore's stop-go traffic gives an engine little airflow to recover. Timing failure from a snapped belt or stretched chain lets valves and pistons meet, bending valves in seconds.
Poor previous repairs cause more failures than owners expect — an engine built without measured clearances fails again quickly. Fuel quality damages injectors and pumps, and high mileage wears rings, guides and bearings until compression and oil control drop below usable limits. Regular oil changes and cooling-system checks prevent most of these failures, and a fault code that will not clear may point to ECM repair and diagnosis rather than the engine itself.
The right choice depends on what the inspection finds, not the symptom you arrived with.
Repair suits a contained failure when the rest of the engine measures healthy — a head gasket, timing chain, oil pump or turbo, with block, bores and bearings still in spec.
Rebuild suits wear spread across the engine: low compression in several cylinders, bearing knock, heavy oil burning, or a history of overheating. It restores surfaces and clearances instead of patching a symptom.
Replacement makes sense when the block or head is cracked beyond machining, when parts are unavailable, or when restoring the engine costs more than a sound replacement unit.
When a part is not made any more, we can machine a new one instead.
That decision comes after teardown and measurement. Anyone quoting a rebuild before opening the engine is guessing.
We rebuild both, and the work differs. Diesel engines run far higher compression, so they demand tighter tolerance control and closer attention to head and deck flatness and injector seats. Diesel rebuilds usually include the injection system, because an untested injector will damage a freshly rebuilt engine, and the turbocharger gets inspected with it.
Petrol engine repair is lighter on the bottom end but more sensitive on the valvetrain and ignition side — valve seats, guides, variable valve timing and ignition sensors. The process stays the same; the failure points differ.
We do not quote engine work over the phone, because an honest number needs an inspection. These factors decide it:
SNZ Auto Engineering Works is an engine rebuild and repair shop in Wilson Garden, Bangalore, not a parts-swapping garage. We invested heavily in machinery you will otherwise find only in the world's top machine shops, so we restore bores, decks, cranks and heads to measured tolerances in-house. The same bench handles a three-cylinder hatchback and a V12 supercar engine, because the measuring does not change with the badge. We built India's fastest car here in Bangalore, and that build set the standard we hold every engine to. If you want more power rather than a repair, see our performance engine builds. Owners come to us from across south Bangalore and beyond.
An engine rebuild takes longer than a service because the engine must come out, be measured, machined and reassembled. The timeline depends on the damage found at teardown, the machining needed and how fast the parts arrive. We give you a date after inspection.
A properly rebuilt engine is restored to correct tolerances, with worn surfaces machined and out-of-spec parts replaced, so it delivers the compression, oil control and power it was designed for. Quality depends entirely on measurement discipline — a rebuild done without measuring clearances is only a reassembly, and it fails again.
Yes. We keep the parts we remove and show you the wear that justified replacing them, along with the measurements we took. That is how you can tell whether the work was needed. A workshop that cannot show you what failed is asking you to take its word for it.
Yes, we rebuild both petrol and diesel engines. Diesel work covers the higher-pressure bottom end, head and deck flatness, injector seats, and inspection of the injection system and turbocharger, because a faulty injector or turbo will damage a freshly rebuilt engine.
Often, yes. If the head has failed — blown gasket, burnt valve or warped surface — and the bottom end still measures in spec, we can machine and rebuild the head alone. We confirm that with compression and leak-down checks first. If the bottom end is also worn, head-only work is a short-term fix.